Número do item 815118

Sopradora Sidel SBO 6/10


Moeda Aceitável de Vendedores:

$75,000.00 USD

Fazer uma oferta

Localização:  OH, Estados Unidos

Nível de Remoção:  

Por que recomendamos inspeções

Não está disponível para remoção até: quinta-feira, 30 de setembro de 2021
O vendedor revisará ofertas sobre este item até a data de retirada.

*Todas as ofertas são enviadas em moeda dos vendedores

Não veja o que você está procurando Nós vamos encontrá-lo para você




Descrição do equipamento
Sidel SBO 6.10 Stretch Blow Molder With Auxiliary Equipment

  • (6) cavities, (10) heat zones
  • Preferential heating
  • Preform loader and elevator, Sidel no. XMRP: 5547 CE Marked
  • Sameto technifil EB box tipper for preforms, CE Marked
  • Operators controls-ABB Pyromat 636
  • Electrical panels
  • Conair micro Trac 2 temperature controller
  • Presently producing ~4100 BPH, capacity can go higher based on bottle configuration and materials
  • System rebuilt ~2012
  • Technical manuals available
  • Equipment still in service and not available until June 30th 2018 and can be inspected while installed

  • Mfgs. standard info, this machine may vari slightly:

    GENERAL INFORMATION
    The SBO 6/10 has 6 molds and 10 heating modules.
    Willwork with a wide range of bottle sizes and styles from 0.25 to 3 liters.

    Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be
    supplied to the machine. Separating the bottle manufacturing and preform manufacturing
    processes allow production to be optimized, provide greater flexibility of operation and
    use, and provide higher production output rates and yield.

    MAXIMUM PREFORM DIMENSIONS

    Neck height 9 - 41 mm (measured from bottom of support ring)
    Minimum inside diameter of neck 19 mm
    Maximum outside diameter of neck 34 mm
    Preform support ring diameter 29 - 51 mm
    Maximum preform length 210 mm

    MAXIMUM BOTTLE DIMENSIONS

    Maximum bottle diameter 130 mm
    Maximum bottle height 380 mm
    Bottle capacity 0.25 - 3 liters

    AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids)

    0.25 liter bottle 14-20 grams
    0.50 liter bottle 20-33 grams
    1.00 liter bottle 26-40 grams
    1.50 liter bottle 35-51 grams
    2.00 liter bottle 44-58 grams
    3.00 liter bottle 68-84 grams


    SBO 6/10 SPECIFICATIONS:

    BLOW WHEEL

    Height 3.5 meters
    Number of molds 6
    Closing force 10 tons
    Item height (under neck) at outfeed 1.4 meters approximately
    Machine DC drive motor power 4 KW

    HEAT CONDITIONING

    Height 2 meters
    Number of oven heating units 10
    Number of heating zones per unit 8
    Maximum power 170 KW

    ELECTRICAL USAGE

    Maximum supplied power 200 KW
    Average consumption 100-150 KW/hr (varies per bottle being produced)

    COMPRESSED AIR

    Supplied power from 7-35 bar
    Pressure 7 bar
    Flow rate 50-100 Nm3/hr (varies per bottle being produced)
    Blow pressure - champagne base up to 25 bar
    Blow flow rate - champagne base 110-550 Nm3/hr
    Blow pressure - petaloid base up to 35 bar
    Blow flow rate - petaloid base 155-770 Nm3/hr

    CHILLED WATER

    Temperature 10-12 degrees Centigrade
    Pressure 5-6 bar
    Flow rate up to 6 cubic meters/hour
    Kcal to be removed up to 16,000 Kcal/hour

    WEIGHT

    Blow wheel with molds 8 tons
    Heat conditioning unit 2.2 tons
    Preform feeder 0.65 tons
    Electrical cabinet 0.85 tons

    OVERALL DIMENSIONS (including open gate access etc)

    Length not including preform feeder 4.0 meters (157 inches)
    Length including preform feeder 9.3 meters (336 inches)
    Width 6.4 meters (252 inches)


    DESCRIPTION AND OPERATION OF SIDEL SBO 6/10 STRETCH BLOW MOLDERS

    PREFORM FEEDER
    The preforms are held under the support ring by two rails before being lowered by gravity
    to the feeder plate.

    PREFORM HEAT CONDITONING
    The preforms are transferred neck up to the heat conditioning device. This unit
    continuously insures the preforms are inverted before passing, neck down, in front of the
    heating units and then inverts them again. During the heating phase, the preforms are
    rotated and their necks protected from the heat in order to optimize the distribution of
    heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can
    accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The
    heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in
    order to optimize the heat profile. These zones are regulated on all SBO Models. After
    heating, a control by infra-red camera of preform temperature enables regulation of the
    zones under control, thus insuring maintenance of the required temperature.

    PREFORM TRANSFER
    At the outfeed of the heat conditioning unit the preforms are transferred to the blow
    wheel by means of a transfer wheel.

    BOTTLE STRETCH-BLOW
    The blow wheel comprises of 6 molds of the pin type locking system whose opening and
    closing are cam actuated. Each mold, cooled by inner circulation of chilled water, is
    fitted in a mold-holding unit with integral mechanical locking. This system allows quick
    change of the molds. The blow nozzle is then inserted into the neck of the preform, thus
    guiding the stretching rod, which insures the preform's axial orientation. The blow which
    insures side orientation takes place in two stages: medium pressure pre blowing and high
    pressure blowing thus enabling optimum distribution of bottle wall thickness. The blow
    nozzle insures perfect seal whatever the blowing pressure. The blow pressure control is
    integrated into the machine.

    BOTTLE DISCHARGE
    The bottles are discharged from the blow wheel by an outfeed wheel which transfers the
    bottles on a star wheel which pushes the bottles onto the machine outfeed.


    TECHNICAL ADVANTAGES OF SIDEL SBO STRETCH BLOW MOLDERS

    MACHINE RELIABILITY
    Robustness and long lasting service components.
    Transfer and mold open/close motions are controlled by rotary kinematics and fixed cam
    paths.

    PROCESS RELIABILITY
    Constant quality of bottle production based on the precision and repetition of stretch
    motions, and automatic adjustment of camera controlled heating zones.

    PRODUCTIVITY
    High productivity based on synchronization of all cam actuated motions and reduced dead
    times.

    INTERCHANGEABLE MOLD SETS
    Molds can be designed to fit the complete line of Sidel SBO stretch blow molders.

    SIMPLICITY
    A single motor with simple motions actuated by timing belts and gears.

    VERSATILITY
    Cabinet design enables easy access and fast interchange of molds and customization parts.
    Settings for heating, output rate, stretching, pre-blowing, and blowing can be quickly
    and independently changed. The process can be adapted to all types of preforms.

    AUTOMATIC OPERATION
    The main functions of startup and operation are combined on the machine integrated
    control panel. The role of the operator mainly consists of checking preform loading and
    output bottle quality.

    BOTTLE WEIGHT REDUCTION
    Optimization of material distribution based on precision of heat conditioning and stretch
    motions.

    STAFF SAFETY
    Machine startup can only proceed with the doors closed - opening them during machine
    operation triggers an immediate shutdown of the machine. Noise levels are less than 85dB.

    MACHINE SAFETY
    Various safety systems avoid mechanical damage to the machine. Preventative safety
    systems, such as the ejection of sub-standard preforms before heat conditioning, ejection
    of unblown preforms and substandard blown preforms, etc. High speed shutdown of machine
    due to prevent abnormal stress levels etc.


  • Especificações:
    Padrão
    Métrico

    Nome do fabricante
    Sidel
     

    Ano:
    1991
    1991

    Número de Série:
    5059
    5059

    Modelo:
    SBO 6/10
    SBO 6/10

    Velocidade:
    4100 BPH
    4100 BPH

    Produtos Transportados:
    Household products bottles
    Household products bottles

    Forma Recomendável da Embalagem:
    6C (6X6X6)
    6C (6X6X6)


    Dimensões:
    Padrão
    Métrico

    Total:
    1 x 1 x 1 IN - 1 LBS
    25,40 x 25,40 x 25,40 mm - 0,45 kg


    aviso Legal

    Este lote se vende "no estado em que se encontra". Recomendamos que contate um representante de vendas da EquipNet para agendar uma inspeção. Este artigo se encontra em

    OH

    Este equipamento está sujeito a taxas de desinstalação e remoção.


    A descrição por escrito fornecida para este equipamento representa EXATAMENTE aquilo que você receberá se optar por comprar este item. Todos os artigos que não estão na descrição, mas aparecem nas representações visuais deste item não serão incluídos na venda. Fotos e vídeos são fornecidos apenas como referência e para dar uma noção geral do estado dos itens.

    Clientes que visualizaram isso