Listing# 772525

Wabash 4-150 Ton Vacuum Hydraulic Press

Seller's Acceptable Currency:

$32,500.00 USD

Make An Offer

Location:  RI, USA

Level of Removal:  Uncrated/Loose

This listing is EquipNet Certified
Learn More

*All offers are submitted in Seller’s Acceptable Currency

Don't see what you're looking for? We'll find it for you

Equipment Description
Wabash 150 Ton Vacuum Hydraulic Press

    4 - 150 ton compression force (adjustable)
    Heavy-duty slab side construction
    18" L-R x '18" F-B fully guided heated platens cored for cooling
    80O deg. F (426 degrees C) maximum operating temperature
    Vacuum rated cartridge heaters
    insulation between platen and bolster
    Perimeter insulation
    Single opening with:
    12" op€n daylight
    0" closed daylight (shut height)
    12" bore JIC style clamp cylinder
    12" stroke
    integral vacuum chamber, including:
    Front hinged door with interlock switch
    Rear hinged door with interlock switch
    3" NPT port for connection lo vacuum source
    Self-contained hydraulic system. including:
    Energy-efficient TEFC motor
    Dual gear pump system
    35 gallon reservoir with access panel and gauge for oil level and
    temperature indication
    Suction line strainer
    Water-cooled heat exchanger
    10 micron absolute return line cartridge filter
    75 IPM closing speed
    0-5 IPM pressing speed - adjustable
    60 IPM opening speed
    NEMA-rated electrical control enclosure, including:
    ViewPoint control system including:
    Allen Bradley Compact Logix programmable controller with PaneView 600
    Plus touch screen
    Closed-loop control of clamp pressure
    Closed loop control of platen temperature
    Position control
    Each control zone includes:
    Programmable segments
    Display of set point vs. actual
    Programmable rate of increase or dec,rease of pressure and temp
    increase ramp
    Linear transducer
    Set up mode for mold alignment
    460/3/60 supply voltage
    Non-fused disconnect
    Electrically heated platens package
    Vaewpoint control system for ramping of pressure, and temperature rise as
    well as position control
    Automatic low pressure system
    Automatic platen cooling
    Bolsters cored for water cooling
    Nitrogen purge system for vacuum chamber
    Two thermocouple receptacles for part monitoring
    Full machine documentation on CO, including operating manual and
    Pressing speed control
    Heater burn out detection through the PLC

  • Also includes a small stainless steel tank and chiller It is currently programmed to blow air thru the cooling circuit until it comes down to 200F and then switches over to water cool mode. It can be set up for hot and cold oil as well
  • The machine is in almost new condition with a little more than 2000 hrs running time and 170 cycles

  • New price in 2011-over $125,000

  • Specifications:

    Manufacturer Name


    Serial Number:

    Tonnage Rating:
    150 TONS
    150 TONS


    Design Speed:
    75 IPM closing speed 0-5 IPM pressing speed - adjustable 60 IPM opening speed
    75 IPM closing speed 0-5 IPM pressing speed - adjustable 60 IPM opening speed

    Shut Height:
    0” closed daylight (shut height)
    0” closed daylight (shut height)

    460 VOLTS
    460 VOLTS

    60 HERTZ
    60 HERTZ



    80 x 40 x 80 IN - 14000 LBS
    2032.00 x 1016.00 x 2032.00 mm - 6350.40 kg


    This lot is being sold "as is, where is". We recommend that you contact an EquipNet sales representative to set up your own inspection. This item is located in


    This equipment is subject to a removal and loading charge.

    The written description provided for this equipment is EXACTLY what you will receive if you opt to purchase this listing. Any items that are not in the description but appear in the visual representations of this listing will not be included in the sale. Photos and video are provided just as references and to give a general sense of condition.

    Please be aware that weights and dimensions of equipment provided on EquipNet’s listings are estimates and can vary from actual weights and size. Sellers estimates are often not precise especially when equipment was installed versus prepped for shipment. As such, please do not fully rely on the accuracy of this information in EquipNet’s listings for shipping quotes and/or user size requirements.

    Any license associated with this equipment is non-transferable.