Lot 18 Listing# 1046528

Carrier 39MN14WL4848211XXE Air Handling Unit


You must be logged in to participate in auctions

Log in



Location:

Pheonix, AZ, USA

Event Start Date:

11/3/2026

Invoices Will be Sent:

11/9/2026
All invoice payments are due immediately upon receipt.

Equipment Description
Carrier model 39MN14WL4848211XXE indoor air handling unit from the 39M series, serial 2818U36617, nameplate marked for service as AHU-3,17 and field-tagged AHU-17 on the fan section. The unit is a horizontal, multi-section air handler in a galvanized steel casing with hinged, latched access doors at each section for filter, coil and fan service, and is set on a floor-mounted steel support frame with ducted supply and return connections. Per the unit nameplate, the airside arrangement runs (A) mixing box, (B) flat filter section with pre-filters of (3) 16x20 and (3) 20x20 and main filters of (3) 16x20 and (3) 20x20, (C) chilled water and hot water coil section with plenum - chilled water coil 28MCV828FAA059BLNA and hot water coil 28MHV228HAA059BLNA, both rated 300 psig maximum operating pressure at 200 F, (D) blow-thru supply fan section with two 5 HP motors (10 HP total) at 1800 RPM, 460/3/60, 6.6/8.3/10 FLA/MCA/MOCP each and 15.4 maximum continuous amps, fan 39MBH9FVB29014FCCK, motor 93MS0725BA280X0XSB, VFD 93VFHJH07D21JBXXCX, and (E) discharge plenum. Visible controls and accessories include an ABB variable frequency drive with a lit keypad display mounted on the fan section, an Eaton heavy duty safety switch (30 A, 600 V) fed from panel 3DPH2 circuits 25, 27, 29, a motor-mounted disconnect, and a DriSteem Vapor-logic steam humidifier control cabinet mounted at the mixing box end of the unit. Chilled water supply/return, heating water supply/return and condensate piping are run to the unit with insulated headers and isolation valves. The unit is currently installed in place, hard-piped, ducted and wired, and will require disconnection by trades and rigging to remove. The ABB drive display was illuminated at the time of the site visit.

Powers On Explanations

ABB variable frequency drive keypad display is lit (green backlight with active readout) in photo 4, and the unit is energized through the Eaton disconnect.

Specifications:
Standard
Metric

Manufacturer Name

Carrier Corporation
 

Serial Number:

2818U36617
2818U36617

CE Marked:

UNKNOWN
UNKNOWN

Model:

39MN14WL4848211XXE
39MN14WL4848211XXE

Capacity Size:

10 HP
10 HP

Capacity Speed:

1800 RPM
1800 RPM

Capacity Details:

Sections: (A) mixing box; (B) flat filter - pre: (3) 16x20, (3) 20x20, main: (3) 16x20, (3) 20x20; (C) chilled water and hot water coils with plenum,
Sections: (A) mixing box; (B) flat filter - pre: (3) 16x20, (3) 20x20, main: (3) 16x20, (3) 20x20; (C) chilled water and hot water coils with plenum,

Voltage:

460 VOLTS
460 VOLTS

Frequency:

60 HERTZ
60 HERTZ

Phase:

3
3

Current:

15.4 AMPS
15.4 AMPS

Recommended Packaging Form:

PALLET
PALLET


Dimensions:
Standard
Metric

Overall:

168 x 60 x 60 in - 3000 lbs
4267.20 x 1524.00 x 1524.00 mm - 1360.80 kg


Certain sellers requires that we assess state sales tax where applicable. Sales tax can only be waived if a valid sales tax exemption certificate is provided.

This lot is being sold "as is, where is". We recommend that you contact an EquipNet sales representative to set up your own inspection.

This equipment is subject to a removal and loading charge.

The written description provided for this equipment is EXACTLY what you will receive if you opt to purchase this listing. Any items that are not in the description but appear in the visual representations of this listing will not be included in the sale. Photos and video are provided just as references and to give a general sense of condition.

Please be aware that weights and dimensions of equipment provided on EquipNet’s listings are estimates and can vary from actual weights and size. Sellers estimates are often not precise especially when equipment was installed versus prepped for shipment. As such, please do not fully rely on the accuracy of this information in EquipNet’s listings for shipping quotes and/or user size requirements.

Any license associated with this equipment is non transferable.

EquipNet, Inc. Auction Terms

  • All auction equipment is subject to internal redeployment, cancellation of listing, or other sale prior to formal acceptance of an auction bid by the seller.
  • All bids are binding. Once bids are submitted you cannot remove or modify them, although you can place additional bids. If you make a mistake in your bid, please call our hotline and a Sales Representative will assist you.
  • All items, unless otherwise stated, are sold “As Is, Where Is, With All Faults”.
  • The sale of equipment is intended to be sold without software or other proprietary intellectual property including but not limited to manuals (“Software”), if any is applicable. 
  • Handling Fees: are noted where provided by the vendors. Please see item description for more details. This is the cost to get the item from its location to an area where it can safely be loaded (unless otherwise noted). Packaging and Shipping are additional and can be provided once your equipment invoice has been paid.
  • Auctioneer has ownership or financial relationships with companies that may be participating in the auction to purchase and take ownership of an item. Any such bidding activity will be conducted transparently and in full compliance with all applicable laws, regulations, and recognized industry standards. No bidding will be done to influence prices and only for the purpose of taking ownership.
  • Buyer's Premium is 19% - The premium is a percentage of the final price of a listing (item) that is in addition to the equipment sale price. For example, if an auction charges a buyer’s premium of 19% for amounts below $1,000, you will be required to pay an additional $190 for a lot totaling $1,190.
  • Taxes / VAT: Sales tax may be applied to your purchase, depending on your state and exemption status. If no sales tax is applied to your order, check your state's sales and use tax requirements as you may be required to self-assess any tax required.
  • Your invoices are sent via email initially and can also be viewed from the My EquipNet section of the website. Our payment instructions can be found at the bottom of your invoice. Acceptable payment Methods include credit card with a max of $10,000 USD (Visa, MasterCard, Discover, AmEx), otherwise Wire Transfer ONLY. EquipNet DOES NOT accept checks, PayPal or PO's as payment. All invoices must be paid within (5) days of receipt of invoice.
  • Invoices must be paid in full before shipping/pick-up arrangements can be made. Once paid in full, a member of the EquipNet Logistics department will contact you regarding your freight quote.
  • All items must be removed within the specified removal period or shall be deemed abandoned and resold by EquipNet, Inc. All quotes must be obtained after the auction has concluded and the item(s) have been paid for. Abandoning items can result in being banned from future bidding.

To read full terms and conditions, click here.